Stack 52mm Pro-Control Stepper Motor Analogue Gauges

Stack Pro Control Stepper Motor range of analogue gauges are user configurable with Maximum/Minimum alarms which can be set with one of seven different colours to indicate status.

Stack’s Pro-Control range of Professional Stepper Motor Analogue Gauges brings total control and driver awareness of critical engine functions.

The Pro-Control series has all of the features of the Professional Analogue Gauges plus:

• Peak “tell-tale” Memory - Max temps, Min pressures
• Configurable max and min full dial alarm warnings
  
• Configurable Pro-Control output for activating accessories eg. fans, pumps, etc (requires relay)
  
• Temperature gauges with built-in “fan controller”
  
• Pressure gauges with built-in “pump controller”
  
• 0-5 Volt analogue output for data logger or ECU (except Boost Pressure, EFT and Fuel Level gauges)
  
• Configurable backlight colour
  
• Black dialface when powered off

52mm diameter Fast, smooth stepper motor needle drive 270° full sweep movement for excellent readability Remotely mounted solid-state sensors keep hazardous fluids in the engine compartment Better than 2% accuracy All-electronic design for maximum reliability 7 Colour LED through-the-dial backlighting 7 Colour LED illuminated needle

Full-dial alarm warning

User-configurable minimum and maximum alarms can be set, with one of seven different colours assigned to each.

As soon as an alarm level is exceeded, the full dialface changes colour. If the level exceeds the alarm by more than 10%, the dialface flashes rapidly to further alert the driver.

With a choice of 7 user-selectable LED backlighting colours ( red, green, yellow, blue, purple, turquoise and white) the user can choose the optimum colour for maximum visibility and readability of the gauge, day and night.

Pro-control feature *eg. built-in fan controller)

The Pro-Control feature activates low and high outputs whenever the user-defined alarm levels are exceeded. Pro-control outputs can be used to switch a relay to activate cooling fans, pumps, lamps, alarms, ignition kill etc.

Press and hold the PEAK button to recall on the dial the highest temperature or lowest pressure or voltage since the memory was last reset.

Unrivalled accuracy
Precision stepper-motor needle movements and solid-state sensors ensure better than 2% accuracy.

Sensors & Wiring Harness Included
All Stack 52mm Professional gauges come complete with wiring harness and associated solid-state sensor (except for Fuel Level and Battery Volts).

Oil Pressure
Pro-Control Professional Stepper Motor Analogue
ST3501			ST3502
0 -7 BAR			0-100 PSI
M10x1			1/8NPT

Fuel Pressure (low)
Pro-Control Professional Stepper Motor Analogue
ST3503			ST3504
0 -1 BAR			0-15 PSI
M10x1			1/8NPT

Fuel Pressure (high)
Pro-Control Professional Stepper Motor Analogue
ST3505			ST3506
0 -17 BAR			0-100 PSI
M10x1			1/8NPT

Water Temperature
Pro-Control Professional Stepper Motor Analogue
ST3507			ST3508
40-120°C			100-260°F
1/8NPT			1/8NPT

Oil Temperature
Pro-Control Professional Stepper Motor Analogue
ST3509			ST3510
40-140°C			140-280°F
1/8NPT			1/8NPT

Boost Pressure
Pro-Control Professional Stepper Motor Analogue
ST3511			ST3512
-1.0 to +2.0 BAR			-30inHg to +30 PSI
M10x1			1/8NPT
Note: This guage does not feature 0-5 Volt analogue output for data logger or ECU.			Note: This guage does not feature 0-5 Volt analogue output for data logger or ECU.

Exhaust Gas Temperature
Pro-Control Professional Stepper Motor Analogue
ST3513			ST3514
0-1100°C			0-2000°F
1/8NPT			1/8NPT
Note: This guage does not feature 0-5 Volt analogue output for data logger or ECU.			Note: This guage does not feature 0-5 Volt analogue output for data logger or ECU.

Fuel Level
Pro-Control Professional Stepper Motor Analogue
ST3515
Programmable
Note: This guage does not feature 0-5 Volt analogue output for data logger or ECU.

Battery Voltage
Pro-Control Professional Stepper Motor Analogue
ST3516
8-18 V

Customer Application

The above installation of Pro-Control gauges is from Studie AG's project car Z4 (see above). Often called "The Coolest Tuning Shop in the World", the company is run by Yasuaki "Bob" Suzuki, a BMW aficionado. He has tuning centers in several cities, including Kobe, Sendai with the headquarters is in Yokohama City. However, Studie recently opened a new showroom and workshop facility in Tokyo. The gauges are supplied in Japan by 3D Design.

Specifications

Where to buy Stack

Frequently Asked Questions

This page last revised